Punches and back gauge of a JUGAO press brake with a bent part on the table

Selection center

Start withthe part.

Material, thickness and bend length in. Force, die and a matching machine out, checked by an engineer when it matters.

Sizing

Which frame
takes your bend?

Air-bending force for a 90° bend, set against our four 3200 mm press brakes. The orange line is the force your part needs: every frame it cuts through is too small.

MaterialK 1.15
4.0 mm
3048 mm · 10.0 ft
Die openingV 32 mm

P = 65 × S² × L ÷ V × K · t, mm, m. K for A36 already carries a 15% margin.

V 32 mmS 4.0 mmb ≥ 22.4
Required force113.9t
Die opening
V 32 mm
Inner radius
≈ 5.1 mm
Shortest flange
≥ 22.4 mm
Punch
88° / 86°
  • 80 t × 3200Deflection compensation at 10 ftToo smallMax 2.8 mm here
  • 100 t × 3200Entry size for high-mix shopsToo smallMax 3.5 mm here
  • 160 t × 3200CNC mechanical crowning advisedSmallest fit71% load · max 5.6 mm
  • 250 t × 3200Check throat and open heightFits46% load · max 8.7 mm

Materials

Thickness,
by material.

What each frame bends in mild steel, stainless and aluminum, and how we prove it on a trial bend. Each bar is the plate, from thinnest to thickest.

100 t × 3200 mm

Length up to 3200 mm
  • Q2350.5–10
  • SS3040.5–6
  • AL 5052 · 60610.8–12

Dies · thin V6/8/12 · medium V16/20 · thick V25/63/80

160 t × 4000 mm

Length up to 4000 mm
  • Q2350.5–14
  • SS3040.5–8
  • AL 5052 · 60610.8–16

Dies · thin V6/8/12 · medium V16/20 · thick V32/80/100 · cosmetic parts on anti-mark film, marks ≤ 0.05 mm

200 t × 4000 mm

Length up to 4000 mm
  • Q2350.5–16
  • SS3040.5–10
  • AL 5052 · 60610.8–20

Dies · V12/16/20/25/32/40/80/120 · no thick plate in a small V; the first part is kept and saved to the material library

Changing material

Stainless 304
Hold to 65–70% of the mild-steel thickness. Open the die to 8–12 × t and allow 3–5° for springback.
Q355
Take 15–20% off the mild-steel thickness.
6061-T6
Inner radius at least 1 × t.

Trial-bend acceptance

Angle
±0.5° structural · ±0.3° precision

Drawings

What we read
off your drawing.

Every field we ask for is a line on the drawing or a fact about your floor. Point at a field to see where it sits. Anything missing, we ask for before we size.

tbRi90°Lbend lineMATERIALgrade · tensileSURFACEmarks · filmDXF · DWG · STEP · PDF · units
Within 2 h · Pre-salesPre-screen

Fields checked; anything missing is asked for.

Within 4 h · Application engineerStandard selection

Machine and reference configuration.

Within 24 h · Only if a rule below is hit3D simulation

The part is bent in DELEM 3D before we commit.

Engineering managerSigned off

No quote leaves without the final signature.

Goes to an engineer when

Q355, 6061-T6, titanium-copper or stainless above 70% of the reference thickness

A flange under 0.7 V, or a hole closer to the bend than 2.5 t + Ri

Angles under 30°, hems, bottoming, large radii, or offsets under 3 t

Deep boxes where the tooling may collide

No marks allowed (≤ 0.05 mm), or angles tighter than ±0.3°

The partFrom the drawing

  • Material grade and tensile strengthA36 · SS304 · …
  • Thicknesst
  • Longest bendL
  • Shortest flange and target inner radiusb · Ri
  • Target angle°
  • Surface requirementsCosmetic or not
  • 2D or 3D drawingUnits stated

If it is missing, we ask“Please add the exact sheet grade, such as A36 or SS304, and the maximum thickness, so we can size safe tonnage and the V-die.”

Your floorDecides drive and power

  • Daily or monthly volume, and how often parts changeElectric or hydraulic
  • Plant voltagee.g. 480 V · 3-ph · 60 Hz
  • Door height and widthGetting it in

Line balance

Can the brake
keep up with the laser?

One shift, drawn to scale. Orange is bending time; the hatched blocks are die changes. Add changes and watch where the shift goes.

6

Hydraulic · 100 t × 3200 mm

28–35 s a part · 15 min a change

Die changes 1 h 30 minBending 5 h 18 min

One product family: one hydraulic brake keeps up with one laser.

Above 10 changes a shift, waiting on die changes becomes the bottleneck.

All-electric · 100 t × 3200 mm

18–22 s a part · 8 min a change, quick clamps

Die changes 48 minBending 6 h 0 min

About 35% faster a part: room for the cut parts of 1 to 1.5 high-power lasers in high-mix work.

BendingDie change

The example shop

Shift
8 h at 85% uptime = 6.8 h, one skilled operator
Laser feed
240 parts a day, 2.0 mm mild-steel enclosure parts
Each part
4 bends, including the flip

Full line

Cut, bend, weld.
Who owns what.

We can deliver the whole sheet-metal line. The orange part moves through it; under each station, who builds the machine, how it talks to the next one, and who answers for it.

Cut

Fiber laser · CNC shear
Built byJUGAO builds the machine. Laser source and cutting head from tier-one suppliers.
Hands onReads DXF or STEP flat patterns, sends barcode work orders to bending.
Answers for itJUGAO: design, build, commissioning and the whole-machine warranty.

Bend

Press brake · robot cell
Built byJUGAO builds the press brake. The six-axis robot and gripper are third-party, integrated by us.
Hands onBrake and robot interlocked over industrial Ethernet and I/O safety signals.
Answers for itJUGAO: the press brake and commissioning the robot link. The robot keeps its maker's warranty, handled jointly.

Weld

Laser weld · robot weld
Built byJUGAO builds the handheld laser welder. Arc-welding robot stations are third-party.
Hands onFixtures designed around your typical parts, agreed when the drawings freeze.
Answers for itFume extraction ducting and the central gas supply mains are yours.
JUGAOThird-party, integratedCustomer

Engineering review

Send a drawing.
Get an engineer.

Standard selections answered within 4 hours. Parts outside the rules get a written process review within 24 hours.

  • Part drawing: DXF, DWG, STEP or PDF
  • Material and thickness
  • Longest bend or cut length
  • Yearly volume

Write to info@ntjugao.com or message the factory on WhatsApp +86 132 2211 1178.

Drawings (DXF, DWG, STEP, PDF): attach them to an email to info@ntjugao.com, quoting your name.

Contact Us