JUGAO press brake on the showroom floor between two robots

Configure & compare

Drive, axesand control.

Electric or hydraulic, how many axes, which controller: each one set against the work it suits.

Drive

Electric
or hydraulic?

Neither drive wins everywhere. Where the two tonnage ranges overlap, the work on your floor decides: how often parts change, how thick the plate, how long the press holds.

All-electric servo

vs

Hydraulic CNC

High-mix small batches, frequent die changes, short precise strokes on small parts

Suits

Long continuous runs, thick plate at high tonnage, long pressure holds

25–40% above hydraulic
New machine
Lower first cost
≈ 0.5–1% of new price
Consumables a year
≈ 2–4% of new price

No hydraulic oil, no leaks

Oil

Full oil change every 2–4 years

Oil-free upkeep, which counts where hydraulic labour costs most

US service labour

Hydraulic technicians are an expensive trade in the US

Ten-year assumptions on the same 100 t × 3200 mm frame. Energy is measured below, never quoted as a blanket saving.

Measured

Logged for
eight hours.

Average power and cycle time, logged on both samples over 8 hours of continuous work. The two presses stroke at the middle of each measured cycle range.

Samples · 100 t × 3200 mm, one of each drive · 8 h continuous logging

Average power

kW
Electric3.2–4.5Hydraulic6.8–8.2

Cycle time

s
Electric2.2–3.0Hydraulic3.5–4.8

Small batches with two bends a part: the work all-electric is built for.

Same part, side by side

Electric

0cycles

Average power
3.2–4.5 kW
Cycle
2.2–3.0 s

Hydraulic

0cycles

Average power
6.8–8.2 kW
Cycle
3.5–4.8 s

Strokes shown at the middle of each measured cycle range: 2.6 s and 4.15 s.

Axes

How many axes
does the part need?

Three kinds of part, three back-gauge set-ups, seen from above. Pick a part and the drawing shows what moves.

2axes · Y and X

6+1axes

8+axes · angle measurement · front supports

BACKOPERATOR SIDEfront supportsangle measurementYY1Y2torsion bar ties both endsXZ1RZ2R

Unequal flanges, boxes

Axes
Y1 + Y2 + X + Z1 + Z2 + R + ΔY, 6+1 axes
Controllers
JUGAO T15 (6+1), DELEM DA-58T (6+1)
Fitted
The mainstream set-up on electro-hydraulic machines. R standard from the mid range up; Z1 and Z2 standard on 6+1.

Controllers

Controllers,
counted in axes.

Each controller drives a fixed number of axes. No option is sold past that count, and the safety kit follows the country the machine is going to.

E21ESTUN · simple parts2
T15JUGAO · medium parts6+1
DA-58TDELEM · medium parts6+1
DA-69TDELEM · complex partsUp to16
AxisThe +1 axisNot available

Safety

Every machine
Emergency stop, a foot pedal with its own e-stop, overload protection
North America · EU
Safety monitoring module and a laser guard (DSP or Lazersafe), required on machines going to North America (OSHA) and the EU (CE)

One BOM

One model,
four documents.

Every model has its own versioned bill of materials. The spec page, the quote, the manual and the build list carry the same model name and axis count, and change together.

Version on all four · V1.0

Website

Spec page

Model name
Axis count
V1.0V1.1Public

Sales

Quotation

Model name
Axis count
V1.0V1.1Per order

Operator

Manual

Model name
Axis count
V1.0V1.1Ships with it

Factory

Production BOM

Model name
Axis count
V1.0V1.1Builds it

Never past the controller

An ESTUN E21 drives 2 axes, so Z1, Z2 and R cannot be ticked on an E21 machine, on any of the four documents.

  • Y
  • X
  • Z1
  • Z2
  • R

Engineering review

Send a drawing.
Get an engineer.

Standard selections answered within 4 hours. Parts outside the rules get a written process review within 24 hours.

  • Part drawing: DXF, DWG, STEP or PDF
  • Material and thickness
  • Longest bend or cut length
  • Yearly volume

Write to info@ntjugao.com or message the factory on WhatsApp +86 132 2211 1178.

Drawings (DXF, DWG, STEP, PDF): attach them to an email to info@ntjugao.com, quoting your name.

Contact Us